← Back to Software Safety Audit Process
SIL / ASIL / Class / PL Class 3B Laser Governance Audit & Sign-Off Authority

Safety Levels (SIL, ASIL, Class, PL) & Class 3B Laser Audit Roles

How safety integrity scales differ across international standards, what level of audit independence each requires, and who is legally and technically qualified to audit and sign off on Class 3B laser systems.

1. Differences Between SIL, ASIL, Software Safety Class & Performance Level (PL)

Different industries use different standards to measure how dangerous a failure can be and how strictly the software and hardware must be verified. While the names differ, all four scales share the same core rule: higher potential harm requires stricter independence between the author and the assessor.

Scale Governing Standard & Domain Levels (Lowest → Highest Risk) What It Measures Minimum Audit Independence
SIL
Safety Integrity Level
IEC 61508
(General industrial, E/E/PE systems, bench & process controls)
SIL 1 → SIL 2 → SIL 3 → SIL 4 Target risk reduction / probability of dangerous failure per hour (PFH) or on demand (PFD). • SIL 1: Level I1 (same-team peer) or I2.
• SIL 2–3: Level I2 (independent department) mandatory/recommended; I3 for SIL 3.
• SIL 4: Level I3 (external accredited body) mandatory.
ASIL
Automotive Safety Integrity Level
ISO 26262
(Road vehicles & automotive subsystems)
QM → ASIL A → ASIL B → ASIL C → ASIL D Severity (S), Exposure (E), and Controllability (C) of a vehicle hazard. • ASIL A: Level I1.
• ASIL B–C: Level I2 (independent confirmation review).
• ASIL D: Level I3 (external/fully independent confirmation).
Software Safety Class IEC 62304
(Medical device software & clinical systems)
Class A → Class B → Class C Consequence of software failure: no injury (A), non-serious injury (B), or death/serious injury (C). • Class A: Level I1.
• Class B–C: Level I2 independent verification, ISO 14971 risk controls, full traceability.
PL
Performance Level
ISO 13849-1
(Machinery & industrial safety interlocks under EU Machinery legislation)
PL a → PL b → PL c → PL d → PL e Ability of safety-related control parts (Category B, 1, 2, 3, 4) to perform a safety function under fault conditions. • PL a–b: Single-channel possible.
• PL c–d: Independent verification (Level I2) + hardware redundancy.
• PL e: Dual-channel hardware (Cat. 3/4) + Level I2/I3 validation.
Approximate Cross-Standard Mapping:
• Low Risk: SIL 1 ≈ ASIL A ≈ Class A ≈ PL b/c
• Medium-High Risk (Serious Injury Possible): SIL 2 ≈ ASIL B/C ≈ Class B ≈ PL d
• High / Catastrophic Risk (Irreversible Injury / Death): SIL 3 ≈ ASIL D ≈ Class C ≈ PL e

2. Specifically for Class 3B Lasers (IEC 60825-1): Why Risk Is High

Under IEC 60825-1 (Safety of Laser Products), a Class 3B laser (typically 5 mW to 500 mW continuous wave, or equivalent pulsed energy) presents an immediate ocular hazard: direct intrabeam viewing can cause permanent retinal or corneal injury faster than the human blink reflex. Because irreversible eye damage is a high-severity hazard, safety functions that enable, unblock, or interlock a Class 3B emitter are treated at SIL 2 / SIL 3 or PL d / PL e equivalence—never as a trivial Class A / SIL 1 software check.

Software Cannot Be the Sole Guard for a Class 3B Laser: Under IEC 60825-1 (Clauses 6.2–6.7) and ISO 13849-1, Class 3B products require physical engineering controls (protective housing, remote interlock connector, key control, emission indicator, and beam attenuator/shutter or physical filter). A PC tool or QR label scan (such as checking a scanned string) is an administrative/procedural check—not a hardware safety interlock.

3. Who Needs to Audit & Verify Class 3B Laser Software and Hardware?

Under IEC 61508-1 (Clause 6 & Clause 8), ISO 26262-2, and ISO 13849-1, the reviewer must be both independent and competent in functional safety. Neither the code author nor an unqualified peer can perform this audit:

Option 1 — Internal Independent Safety / QA Team (Level I2, Same Company)

  • Who: A dedicated QA / Verification Engineer and/or Internal Functional Safety Engineer from a separate department (different manager and reporting line from the software development team), paired with Electrical / Systems Engineering + Laser Safety Officer (LSO) for physical interlocks (IEC 60825-1, ISO 13849-1).
  • When Sufficient: Valid for SIL 2–3 / ASIL B–C / Class B–C (and typical Class 3B interlock verification) only if they have documented functional safety competence/training and execute real negative testing, boundary checks, and fault injection on hardware/mock benches.

Option 2 — Certified External Third-Party / Notified Body (Level I3, Outside Company)

  • Who: An accredited external certification or inspection body (e.g., TÜV, DEKRA, UL, SGS).
  • When Required:
    1. Highest risk levels (SIL 4, ASIL D, high-risk Machinery Directive Annex IV / Regulation (EU) 2023/1230 Annex I).
    2. When a customer, defense/medical buyer, or regulator contractually requires an external third-party certificate.
    3. When the company does not have a qualified, independent internal Level I2 safety assessor.

4. Who Signs Off the Final Documents? (Specifically for Class 3B Lasers)

Document / Decision Who Signs Off Developer's Role
Technical Safety Verification Report
(Software & Hardware Interlock Evidence)
Independent Safety / QA Assessor (Level I2 or certified Level I3 body) + Hardware / Systems Safety Lead + Laser Safety Officer (LSO). Does NOT sign compliance. Supplies the command analysis, pinned Git commit/version, and unit test coverage as technical input.
Legal Declaration of Conformity
(CE Marking / Product Safety / Machinery DoC)
Authorized Corporate Officer / Legal Representative only (e.g., Managing Director, VP of Engineering, Head of Quality & Regulatory). Never signs. Developers have no statutory authority to sign Declarations of Conformity.
Risk Acceptance / Waiver
(If management waives or defers verification)
Management / Corporate Officer only, logged in writing in an immutable company system. Never signs. Logs the known limitation/gap in writing and requests written management confirmation.
← Back to Software Safety Audit Process